How to lift AHU for installation?

No answer Required watch this

Comments

Post a Comment

want to learn more or want any ebooks let me know

Popular posts from this blog

Shop Drawings (Before Work Commences)

What is a Shop Drawing? A shop drawing is a detailed execution drawing prepared by the contractor/vendor based on: Approved GFC / IFC drawings Specifications Site conditions Material finalization It translates design intent into buildable instructions. 👉 No work should start on site without approved shop drawings. --- Primary Intent of Shop Drawings (Before Work Commences) The shop drawing must clearly establish HOW, WHAT, WHERE, and WITH WHAT the work will be executed. 1. Design Intent Confirmation The drawing should: Match approved GFC / IFC drawings Respect design dimensions, levels, and finishes Reflect client + consultant approvals Highlight any deviation / value engineering clearly 📌 If design intent is unclear → RFI must be raised before submission. --- 2. Constructability & Execution Clarity The drawing must show: Exact dimensions (no assumptions) Levels (FFL, AFL, ceiling levels, slab levels) Fixing methodology Sectional details at critical junctions 📌 Anyone on site (f...
Read more

EPOXY FLOOR

Image
EPOXY FLOOR A step guide on how to apply epoxy floor paint. The below guide is a summary of the steps required to coat a floor with epoxy floor paints. This guide applies to a simple roller applied two-coat floor. Such floors are suitable for light and medium wear and tear, perfect for garages and storage rooms. Step 1. Prepare the surface. Preparation of the substrate is necessary in order to ensure adhesion between the epoxy product and the substrate. Suitable methods are sanding or diamond-grinding. Any surfaces that have been contaminated with oils may also require chemical cleaning. Prepare the surface with a suitable floor grinder. Step 2. Sweeping and cleaning of the floor. Use an industrial vacuum that picks up even small dust particles. The floor must be cleaned of all dusts and residues before starting to prime. Otherwise you will have various particles trapped within the coat and adhesion will be significantly weakened. The less micro-dust on the surface...
Read more

Why Concrete Post Is Required Around Metal Door Frame

Why Concrete Post Is Required Around Metal Door Frame 1. Structural Strength & Load Transfer Metal doors (fire doors / heavy-duty doors) impose: High self-weight Repeated dynamic loads due to opening/closing Closer impact loads A concrete/RCC post: Transfers loads directly to slab Prevents frame distortion Avoids long-term sagging of shutter 📌 Especially important when walls are AAC / gypsum / lightweight blocks. 2. Proper Fixing of Door Frame Concrete backing allows: Mechanical anchors / holdfasts to grip properly Avoids pull-out failure Maintains door squareness 📌 Chemical anchors perform poorly in AAC blocks without backing. 3. Fire & Safety Compliance (Critical for Fire Doors For fire-rated doors: Solid backing is mandatory for fire rating integrity Prevents early failure during fire exposure 📌 Most fire door manufacturers clearly state this requirement. 4. Alignment & Long-Term Performance Concrete post ensures: Frame remains plumb & level Door closer works effe...
Read more

Process of Microcontrete Flooring

Image
Process of Microcontrete Flooring  Process On Tile/Marble Flooring  1 Sand The floor with Metal Grinder & Metal Diamond Wheel.  2 Clean the surface ensuring there is no dust on the surface  3 Apply 1 coat of Colortek Neogrip – F primer in thin layer – no dilution required  4 Let dry for 8 hrs  Application Process for Base & Topcoat   1. Apply 1st base coat of  base coat, polymer 3kgs, water 1 kgs, base coat filler 12  kgs mix it well until all lumps are dissolved and it becomes a smooth paste. (3:1  IS RATIO FOR POLUYMER AND WATER MIXING. 4:1 IS RATION FOR POLYMER  WATER MIX WITH POWDER  2. Apply in the thickness of 1-2 mm so that it gives you a coverage of 155 sqft  approx..  3. Let dry for 1 day  4. Sandin to be done by 30# grit resin pad – 8mm thick , Dcrf 7u – then sand with  60# grit resin pad – 3mm  5. Apply – 2 coats of polymer primer by diluting with water 1:1 ratio (1kgs polymer...
Read more

Asian Paints Smartcare waterproofing methodology & work details

Image
USING ASIAN PAINT’S SMARTCARE PU MAGNUM US & SMARTCARE PU INSULATOR & Damp-proof Ultra + Screed     1.0 MATERIALS SPECIFICATION REFERENCE This Method Statement is to be read in conjunction with relevant documentation.   1.     Please refer to PIS of the relevant products mentioned in this method Statement 2.     Safety Data Sheets 3.     Relevant Application Instructions if any from the Manufacturer 2.0 MATERIAL REQUIREMENTS The materials needed for to complete the tasks set forth in this method statement are:   1.     Smartcare PU Ultron 2.     Smartcare Epoxy Primer 3.     Smartcare PU Insulator 4.     Smartcare PU Magnum 5.     Closed Cell Backer Rods for Joints and deep cracks 6.     Smartcare Hy...
Read more

Complete Project Handover and Snagging Process in Construction Projects

Project handover is one of the most critical stages in any construction or interior fit-out project. It represents the transition from execution to final delivery and requires careful planning, coordination, documentation, inspection, and approval processes. A successful handover ensures that all works are completed as per approved specifications, snag points are resolved, documentation is finalized, and the client receives a fully operational and compliant project. Below is a detailed breakdown of the complete project handover and snagging process followed in professional construction management. 1. Final Works Completion Before initiating the handover process, the Project Management team must ensure that all physical works are substantially completed. Key Activities Verify all major construction and finishing works are completed. Ensure all subcontractors have completed their respective scopes. Complete site-wide cleaning and debris removal activities. Ensure all systems are operatio...
Read more

All About Veneer

Image
VENEER Veneers are very thin slices of wood that are glued to a backing material for use in millwork (woodwork, such as doors, window casings, and baseboards) and other elements in an interior. Veneer can be sourced from a number of wood species, and irregularities such as diseases in the wood can lead to beautiful figuring in the final product. Veneers are available in various grades, which affect price and application. Veneer is manufactured in a semiautomated process. A log is debarked, then readied for cutting. Very thin layers are sliced off the log. different cuts and techniques produce a wide range of patterning and texture. Once the cuts have been made, the resulting fitches (a bundle of veneers arranged in the same order as they were cut from a log) are dried and bundled, clipped and joined, to make dimensioned sheets.
Read more

Practical, industry-standard checklist, suitable for interior fit-out projects and factory production

  To manufacture any storage / furniture item in a factory , the factory must receive complete, unambiguous data . Missing even one item can cause wrong fabrication, rework, delay, or site rejection . Below is a practical, industry-standard checklist , suitable for interior fit-out projects and factory production . 1. Approved Shop Drawings (MOST CRITICAL) Factory production should start only after approval . Must include: Plan, elevation, section views Overall sizes (W × D × H) Internal clear dimensions Panel thicknesses Edge profiles (square / chamfer / groove) Fixing details Tolerances (if required) 📌 Status must be Approved or Approved with comments (complied) . 2. Final Site Dimensions (As-Built Data) Required because factory furniture is non-adjustable . Include: Exact wall-to-wall sizes Floor level variations Skirting height & thickness Ceiling height (if full height unit) Column offsets / projections 📌 Site measurement sign-off is mandatory...
Read more